TWF Racing - Forums

Collapse
No announcement yet.

TWF Racing - Forums

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Re: 06 and newer gsxr 600/750 wheel on sv

    Hi guys I just read this whole thread hoping to pickup some info I need to put a 09' sv650 front end on an old 80' cx500.
    I really just need to know the width of the wheel where the discs bolt on.

    Cheers guys and thanks

    Comment


    • Re: 06 and newer gsxr 600/750 wheel on sv

      Sorry double post

      Comment


      • Hi guys, I'm in the middle of a conversion, but as I don't have the original sv setup as example I'm stuck.

        I have a question,
        I already have a machined 6mm offset 525 front sprocket (2 gen SV).
        Does that mean I don't need to machine the sprocket carrier?

        And how much need to be machined of the caliper bracket?
        As the wheel center needs to go 2mm to the right and the RH spacer needs to be 2mm bigger to center the rotor in the bracket, it means I have to machine 4mm off???

        Is there a possibility that I throw my measurements to you in a PB Zoran? So you can check them?

        Comment


        • It is 106mm from center of the wheel to right side swingarm. Put wheel there and adjust rest.

          Comment


          • Thnx zoran!
            With that and my 6mm offset font sprocket in mind, i will have to machine the next things..
            Caliper bracket to 25mm (81.5 (wheel center to caliper bracket inner surface) + 25 = 106.5)
            RH Spacer 17mm (to align the rotor in the middle of the caliper bracket)
            LH Spacer 10mm (to make the whole assembly 239mm)
            1mm of the sprocket carrier spacer. (111 gsxr -6 (offset) -1 = 104mm (stock sv wheel center to sprocket carrier surface).

            This makes a total of 239mm

            Comment


            • Looking for a 17 x 4.5 Marvic or Marchesini, etc. rear SV wheel if possible...

              apologies for crass interruption.

              Cheers,

              F McDermott
              in Canada

              Comment


              • Join the club.
                #60

                Comment


                • 4.5 you probably have to look in to supermoto wheels.

                  Comment


                  • Here is pic from rear wheel GSXR1000L7(2017 model) from greek forum.
                    Weight is in kilos,roughly 9lb 24oz

                    Guy says that compared to K7 it is 70 gr lighter

                    They use same axle,seal and bearings like gsxr 750 K8.
                    Attached Files
                    Last edited by TOLAROS; July 27th, 2017, 01:51 AM.

                    Comment


                    • Hi Zoran,

                      We have a 2005 SV650 and want to purchase your conversion kit for the 06 to 08, GSXR600/750 rear wheel.
                      However, we want to use a BST rear wheel for those bikes instead of the stock wheel.
                      Will it fit?
                      If not what can we do to make it work?
                      Thank you for your time.

                      Comment


                      • No. Kit is made for stock gsxr wheel. It requires sprocket carrier to be machined and would need same done on bst wheel which can be problem. Aftermarket wheels don't usually have enough material to machine from carrier. Some do and some don't. I have not seen bst so I can't tell for sure. Even if carrier can be machined spacers would be different from stock gsxr wheel so to make kit I would need wheel to measure.
                        If you want you can email me picture of carrier from face and side and we can go from there.

                        Comment

                        Working...
                        X